Automation / Innovation

Can your robot debone poultry?

GTRI's Gary McMurray
Gary McMurray, chief of GTRI's Food Processing Technology Division, poses with the Intelligent Cutting and Deboning System, which uses advanced imaging technology and a robotic cutting arm to automatically debone chicken and other poultry products. Source: Gary Meek.

Deboning chicken breasts has always been a labor-intensive job, and not a very safe one at that. Attempts have been tried to design equipment that could successfully debone chicken, but have not enjoyed much commercial success. Researchers at Georgia Tech’s Research Institute (GTRI) have developed a prototype system that uses advanced imaging technology and a robotic cutting arm to successfully debone chicken and other poultry products.

The Intelligent Cutting and Deboning System uses a 3-D vision system that determines where to cut a particular bird. The device automatically performs precision cuts that optimize yield, while also greatly reducing the risk of bone fragments in the finished product.

“Each bird is unique in its size and shape,” says Gary McMurray, chief of GTRI’s Food Processing Technology Division. “So we have developed the sensing and actuation needed to allow an automated deboning system to adapt to that individual bird, as opposed to forcing the bird to conform to the machine.”

With the automated system, a bird is positioned in front of the vision system prior to making a cut. The vision system works by making 3-D measurements of various location points outside of the bird. Then, using these points as inputs, custom algorithms define a proper cut by estimating the positions of internal structures such as bones and ligaments.

“Our statistics research shows our external measurements correlate very well to the internal structure of the birds and, therefore, will transition to ideal cutting paths,” says Michael Matthews, GTRI research engineer. “In our prototype device, everything is registered to calibrated reference frames, allowing us to handle all cut geometries and to precisely align the bird and cutting robot. Being able to test all possible cut geometries should enable us to design a smaller and more simplified final system.”

GTRI's system
A robotic system used in the Intelligent Cutting and Deboning project prepares to slice through the shoulder joint of a chicken. The system, developed by the GTRI Food Processing Technology Division, is pursuing two goals: cutting close to the bone to maximize breast meat yield and ensuring food safety by avoiding creation of bone chips. Source: Gary Meek.

The prototype uses a fixed two-degree-of-freedom cutting robot for making simple planar cuts. The bird is mounted on a six-degree-of-freedom robot arm that allows alignment of the bird and cutting robot to any desired position. The robot arm places the bird under the vision system, and then it moves the bird with respect to the cutting robot.

The system employs a force-feedback algorithm that can detect the transition from meat to bone. That detection capability allows the cutting knife to move along the surface of the bone while maintaining a constant force. Since ligaments are attached to the bone, maintaining contact with the bone allows the knife to cut all ligaments around the shoulder joint without cutting into the bone itself. A similar approach can be used for other parts of the bird where meat must be separated from the bone.

“There are some very major factors in play in this project,” says McMurray. “Our automated deboning technology can promote food safety since bone chips are a hazard in boneless breast fillets. But it can also increase yield, which is significant because every 1 percent loss of breast meat represents about $2.5 million to each of Georgia’s 20 poultry processing plants.”

Did you enjoy this article? Click here to subscribe to Food Engineering Magazine.

You must login or register in order to post a comment.



Image Galleries

Food Engineering's Food Automation & Manufacturing Conference and Expo 2015

Images from Food Engineering's Food Automation & Manufacturing Conference and Expo in Clearwater Beach, Florida, April 12-15, 2015. The event brought food and beverage processors and suppliers together to gain valuable information on the latest trends and technologies in manufacturing, automation, sustainability and food safety.


Burns & McDonnell project manager RJ Hope and senior project engineer Justin Hamilton discuss the distinctions between Food Safety and Food Defense as well as the implications for food manufacturers of the Food Safety Modernization Act.
More Podcasts

Food Engineering

Food Engineering May 2015 Cover

2015 May

The May 2015 issue of Food Engineering explores effective tools for hitting manufacturing targets. Also, read how processors are looking for faster ways to detect harmful pathogens in food and beverages without sacrificing accuracy or reliability.

Table Of Contents Subscribe

Plant Facility/Site Issues

What issue about your current plant facility/site keeps you up the most at night?
View Results Poll Archive


Food Authentication Using Bioorganic Molecules

This text provides critical tools and data needed to augment routine food analysis and enhance food safety by aiding in the detection of counterfeit, and potentially deleterious, foods.

More Products

Clear Seas Research

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications,Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.


FE recent tweets

facebook_40.pngtwitter_40px.pngyoutube_40px.png linkedin_40px.pngGoogle +

Food Master

Food Engineering Food Master 2015Food Master 2015 is now available!

Where the buying process begins in the food and beverage manufacturing market. 

Visit to learn more.