Case Studies & Field Reports

Sausage maker streamlines shrinkwrapping on breakfast line

System upgrade doubles throughput, maximizes line uptime and provides efficient long-term operational ROI.
Williams Sausage, founded by Harold and Hazel Williams in 1958 and located near Union City, TN, runs 11 packaging lines to handle different product types. Four lines are for packaging sausage links and chubs, and four others are for packaging sausage patties. Three lines are dedicated for packaging breakfast biscuit sandwiches, with one line specifically dedicated to jumbo sandwiches. To improve efficiency and accommodate increased throughput, the two remaining breakfast sandwich lines were redesigned to upgrade their shrinkwrap packaging capability.
These two lines allow for the manual assembly and packaging of sausage biscuits. When the sandwiches are being assembled, the biscuits are put through a cutter that slices them in half. The split biscuits move along a conveyor, where sausage patties are manually put between the two biscuit slices. These sandwiches then go through a wrapper, and the sealed biscuits are stacked into cartons. At this point, the two lines merge onto one packaging line, where the cartons are put through a shrinkwrapper, cased, labeled and palletized.
As with any growing business, there were challenges. “Our production volumes had significantly increased,” says Tommy Ray, plant manager at Williams Sausage. “But we needed to double our packaging capability, our throughput of cartons per minute, to keep up with the demand. 
“The bottleneck was our shrinkwrapping system,” continues Ray. “The wrapper was only capable of handling 12 to 14 cartons per minute. But at this rate, we were experiencing line interruptions and delays. We needed to have the ability to shrinkwrap 24 to 28 cartons per minute to keep the sandwich manufacturing lines moving.”
The processor brought in Texwrap Packaging Systems to engineer a shrinkwrap system that would address the throughput and downtime issues. Aside from maintenance issues caused by heavy throughput volumes, the existing L-bar shrinkwrap machine was operating in a cold, damp environment, which caused several problems. The forming of ice crystals, for example, caused drive belts to slip or grab, affecting machine registration. The shrinkwrapper compensated for this by making a longer film bag than necessary, costing more money for film and using more heat energy as well. In addition, the L-bar architecture required running cartons of the same size through the wrapper; otherwise, the machine had to be stopped for changeover to a different carton size. 
Williams installed a Texwrap Model 2202 CR continuous-motion, side-seal wrapper with Motion Trim, Speed Maximizer and Auto-Spacing technologies. With this wrapper, the incoming stream of product does not stop while the end seal is being made, thereby increasing throughput speed. 
With Auto-Spacing control and the ability to vary the conveyor speeds to relax the film between products, the new shrinkwrapping system accommodates randomly fed cartons and accurately separates them for reliable, consistent packaging using the absolute minimum amount of film.
For more information: Tom Dickman, 636-239-7424,

Did you enjoy this article? Click here to subscribe to Food Engineering Magazine.

You must login or register in order to post a comment.



Image Galleries

IPPE 2015

The 2015 International Production and Processing Expo (IPPE) was held in Atlanta at the Georgia World Congress Center, Jan. 27-29. More than 30,000 poultry, meat and feed industry representatives attended the event to interact with the 1,288 exhibitors on the show floor that covered more than 490,000 net square feet. At the show exhibitors demonstrated innovations in equipment, supplies and services utilized by firm in the production and processing of meat, poultry, eggs and feed products.


Burns & McDonnell project manager RJ Hope and senior project engineer Justin Hamilton discuss the distinctions between Food Safety and Food Defense as well as the implications for food manufacturers of the Food Safety Modernization Act.
More Podcasts

Food Engineering

Food Engineering March 2015 cover

2015 March

In this March 2015 issue of Food Engineering, we explore how a surprise FDA audit could be serious if you're not recording key data.

Table Of Contents Subscribe

Plant Facility/Site Issues

What issue about your current plant facility/site keeps you up the most at night?
View Results Poll Archive


Food Authentication Using Bioorganic Molecules

This text provides critical tools and data needed to augment routine food analysis and enhance food safety by aiding in the detection of counterfeit, and potentially deleterious, foods.

More Products

Clear Seas Research

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications,Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.


FE recent tweets

facebook_40.pngtwitter_40px.pngyoutube_40px.png linkedin_40px.pngGoogle +

Food Master

Food Engineering Food Master 2015Food Master 2015 is now available!

Where the buying process begins in the food and beverage manufacturing market. 

Visit to learn more.