Columns

Spray cleaning automated at Dietrich's Milk

Rotary impingement cuts cleaning times, water usage.

Cleaning machines are inserted into the bottom of the cone and connected to a water line affixed to the cone.

The Reading, Pa. facility of Dietrich's Milk Products LLC utilizes vertical spray dryers to produce large quantities of milk powder. With sizes of up to 22 ft. in diameter and up to 60 ft. high, the facility's spray dryers can produce a total upward of 9,000 lbs. of milk powder per hour.

During the manufacturing process, fluid milk is evaporated to 50% solids and then injected under high pressure into the 400° F environment inside the spray dryer where it flash dries. The dry milk then drops to the bottom of the unit and is discharged into bulk containers. Vibrators help remove any powder which may adhere to the sides of the cone. However, over time, the milk builds up on the inside of the dryer and must be removed during routine cleaning. In order to maintain high production efficiencies and product quality, close attention is paid to maintaining the cleanliness of the spray dryer interiors.

Until recently the company utilized traditional spray balls and high pressure water injection to clean the dryers. The routine cleaning cycle usually consisted of two 45 minute wash cycles utilizing a 2% sodium hydroxide caustic solution and a 1% nitric acid wash, interspersed with 20 to 30 minute rinses. A thorough cleaning of the entire unit often required up to 16 separate insertions of the spray ball by cleaning personnel into various openings throughout the dryer. This was a very time consuming, and labor- intensive operation to ensure that all the areas were cleaned. Water usage throughout the process was approximately 250 gallons per minute.

With a standard cleaning process to measure against, Manager of Engineering and Maintenance, Tim Pacilio had the opportunity to install two rotary impingement cleaning machines manufactured by Gamajet Cleaning Systems, Inc. The Gamajet 4 and Gamajet 8 cleaning machines are fluid driven tank cleaners that utilize the cleaning solution for power and provide 360 degree cleaning with low flow rates and high speed. Traditionally used to clean all types of storage and process tanks, this was the first application of a Gamajet unit in a spray dryer.

The Gamajet 4 was inserted inside the large upper chamber and dome of the spray dryer, while the Gamajet 8 is positioned in the smaller sized bustle and cone located at the bottom of the unit. During the new cleaning cycle each Gamajet unit is inserted only once.

With the new units, wash times have been reduced to a 15-30 minute cycle and often only one wash is necessary. Because of the Gamajet's high powered cleaning force, water usage is now estimated to be about 100 gallons per minute.

"We estimate that by using the two Gamajet units, we save about two and a half hours in time and around 7,500 gals of rinse water per cleanup, Pacilio says. "And, we also save on the amount of chemicals we use."

 

This article originally appeared in the February 2004 issue of Dairy Foods.

For more information:
Gamajet Cleaning Systems, 610-408-9940
sales@gamajet.com, www.gamajet.com

Did you enjoy this article? Click here to subscribe to Food Engineering Magazine.

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

IPPE 2015

The 2015 International Production and Processing Expo (IPPE) was held in Atlanta at the Georgia World Congress Center, Jan. 27-29. More than 30,000 poultry, meat and feed industry representatives attended the event to interact with the 1,288 exhibitors on the show floor that covered more than 490,000 net square feet. At the show exhibitors demonstrated innovations in equipment, supplies and services utilized by firm in the production and processing of meat, poultry, eggs and feed products.

Podcasts

Burns & McDonnell project manager RJ Hope and senior project engineer Justin Hamilton discuss the distinctions between Food Safety and Food Defense as well as the implications for food manufacturers of the Food Safety Modernization Act.
More Podcasts

Food Engineering

Food Engineering March 2015 cover

2015 March

In this March 2015 issue of Food Engineering, we explore how a surprise FDA audit could be serious if you're not recording key data.

Table Of Contents Subscribe

Plant Facility/Site Issues

What issue about your current plant facility/site keeps you up the most at night?
View Results Poll Archive

THE FOOD ENGINEERING STORE

Food-Authentication-Flyer-(.gif
Food Authentication Using Bioorganic Molecules

This text provides critical tools and data needed to augment routine food analysis and enhance food safety by aiding in the detection of counterfeit, and potentially deleterious, foods.

More Products

Clear Seas Research

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications,Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

STAY CONNECTED

FE recent tweets

facebook_40.pngtwitter_40px.pngyoutube_40px.png linkedin_40px.pngGoogle +

Food Master

Food Engineering Food Master 2015Food Master 2015 is now available!

Where the buying process begins in the food and beverage manufacturing market. 

Visit www.foodmaster.com to learn more.